华秀塑胶为您提供详细的Noryl PPO V0150B物性表参数。
想了解更多的与Noryl PPO V0150B相关的物性参数，请点击 NORYL™ PPO产品列表。
如果您对我们的Noryl PPO V0150B有任何疑问，或者想索取Noryl PPO V0150B 物性表datasheet、物质安全资料证书MSDS、ROHS检验报告、SGS报告、REACH环保证明、FDA证明、EU法规证明、UL证书及出厂证明COC/COA报告等，敬请拨打我们的服务热线 020-82582555，或者点击 联系我们 给我们留言。
[下载V0150B物性表PDF] 
Consult V0150B
Noryl PPO V0150B Physical property
| Physical |
Nominal Value
|
Unit
|
Test Method
|
|
Specific Gravity
|
|||
|
--
|
1.11
|
|
ASTM D792 |
|
--
|
1.11
|
g/cm3
|
ISO 1183 |
|
Melt Mass-Flow Rate (MFR) (280°C/5.0 kg)
|
3.5
|
g/10 min
|
ASTM D1238 |
|
Melt Volume-Flow Rate (MVR) (300°C/5.0 kg)
|
0.610
|
in3/10min
|
ISO 1133 |
|
Molding Shrinkage -
Flow
|
Internal Method | ||
|
-- 3
|
5.0E-3 to 7.0E-3
|
in/in
|
|
|
0.126 in
|
5.0E-3 to 7.0E-3
|
in/in
|
|
|
Water Absorption
|
ISO 62 | ||
|
Saturation, 73°F
|
0.18
|
%
|
|
|
Equilibrium, 73°F, 50% RH
|
0.060
|
%
|
|
| Hardness |
Nominal Value
|
Unit
|
Test Method
|
|
Ball Indentation Hardness (H 358/30)
|
16400
|
psi
|
ISO 2039-1 |
| Mechanical |
Nominal Value
|
Unit
|
Test Method
|
|
Tensile Modulus
|
|||
|
-- 4
|
363000
|
psi
|
ASTM D638 |
|
--
|
363000
|
psi
|
ISO 527-2/1 |
|
Tensile Strength
|
|||
|
Yield 5
|
10200
|
psi
|
ASTM D638 |
|
Yield
|
10200
|
psi
|
ISO 527-2/50 |
|
Break 5
|
8700
|
psi
|
ASTM D638 |
|
Break
|
7980
|
psi
|
ISO 527-2/50 |
|
Tensile Elongation
|
|||
|
Yield 5
|
5.0
|
%
|
ASTM D638 |
|
Yield
|
4.0
|
%
|
ISO 527-2/50 |
|
Break 5
|
7.0
|
%
|
ASTM D638 |
|
Break
|
10
|
%
|
ISO 527-2/50 |
|
Flexural Modulus
|
|||
|
1.97 in Span 6
|
370000
|
psi
|
ASTM D790 |
|
-- 7
|
348000
|
psi
|
ISO 178 |
|
Flexural Stress
|
|||
|
-- 7, 8
|
16000
|
psi
|
ISO 178 |
|
Yield, 1.97 in Span 6
|
15200
|
psi
|
ASTM D790 |
|
Taber Abrasion Resistance (1000 Cycles, 1000 g, CS-17 Wheel)
|
35.0
|
mg
|
Internal Method |
| Impact |
Nominal Value
|
Unit
|
Test Method
|
|
Charpy Notched Impact Strength 9
|
ISO 179/1eA | ||
|
-22°F
|
2.4
|
ft·lb/in2
|
|
|
73°F
|
6.7
|
ft·lb/in2
|
|
|
Notched Izod Impact
|
|||
|
-22°F
|
3.4
|
ft·lb/in
|
ASTM D256 |
|
73°F
|
6.2
|
ft·lb/in
|
ASTM D256 |
|
-22°F 10
|
2.4
|
ft·lb/in2
|
ISO 180/1A |
|
73°F 10
|
6.2
|
ft·lb/in2
|
ISO 180/1A |
|
Instrumented Dart Impact (73°F, Total Energy)
|
443
|
in·lb
|
ASTM D3763 |
| Thermal |
Nominal Value
|
Unit
|
Test Method
|
|
Heat Deflection Temperature
|
|||
|
66 psi, Unannealed, 3.94 in Span 11
|
284
|
°F
|
ISO 75-2/Be |
|
264 psi, Unannealed, 0.126 in
|
275
|
°F
|
ASTM D648 |
|
264 psi, Unannealed, 3.94 in Span 11
|
266
|
°F
|
ISO 75-2/Ae |
|
Vicat Softening Temperature
|
|||
|
--
|
311
|
°F
|
ASTM D1525 12, ISO 306/B120 12 |
|
--
|
320
|
°F
|
ISO 306/A50 |
|
--
|
293
|
°F
|
ISO 306/B50 |
|
Ball Pressure Test
|
IEC 60695-10-2 | ||
|
257°F
|
Pass
|
|
|
|
284°F 13
|
Pass
|
|
|
|
CLTE
|
|||
|
Flow
: -40 to 104°F
|
4.2E-5
|
in/in/°F
|
ASTM E831 |
|
Flow
: 73 to 176°F
|
3.9E-5
|
in/in/°F
|
ISO 11359-2 |
|
Transverse
: -40 to 104°F
|
4.2E-5
|
in/in/°F
|
ASTM E831 |
|
Transverse
: 73 to 176°F
|
5.0E-5
|
in/in/°F
|
ISO 11359-2 |
|
Thermal Conductivity
|
1.9
|
Btu·in/hr/ft2/°F
|
ISO 8302 |
|
RTI Elec
|
230
|
°F
|
UL 746 |
|
RTI Imp
|
221
|
°F
|
UL 746 |
|
RTI Str
|
239
|
°F
|
UL 746 |
| Electrical |
Nominal Value
|
Unit
|
Test Method
|
|
Surface Resistivity
|
> 1.0E+15
|
ohm
|
IEC 60093 |
|
Volume Resistivity
|
1.0E+15
|
ohm·cm
|
IEC 60093 |
|
Electric Strength
|
IEC 60243-1 | ||
|
0.0315 in, in Oil
|
840
|
V/mil
|
|
|
0.0630 in, in Oil
|
660
|
V/mil
|
|
|
0.126 in, in Oil
|
410
|
V/mil
|
|
|
Relative Permittivity
|
IEC 60250 | ||
|
50 Hz
|
2.80
|
|
|
|
60 Hz
|
2.80
|
|
|
|
1 MHz
|
2.70
|
|
|
|
Dissipation Factor
|
IEC 60250 | ||
|
50 Hz
|
9.0E-4
|
|
|
|
60 Hz
|
9.0E-4
|
|
|
|
1 MHz
|
3.0E-3
|
|
|
|
Comparative Tracking Index
|
250
|
V
|
IEC 60112 |
| Flammability |
Nominal Value
|
Unit
|
Test Method
|
|
Flame Rating
|
UL 94 | ||
|
0.0591 in
|
V-0
|
|
|
|
0.0787 in
|
5VA
|
|
|
|
Glow Wire Flammability Index (0.0394 in)
|
1760
|
°F
|
IEC 60695-2-12 |
|
Glow Wire Ignition Temperature
|
IEC 60695-2-13 | ||
|
0.0394 in
|
1430
|
°F
|
|
|
0.0787 in
|
1430
|
°F
|
|
|
0.118 in
|
1430
|
°F
|
|
|
Oxygen Index
|
32
|
%
|
ISO 4589-2 |
| Injection |
Nominal Value
|
Unit
|
|
|
Drying Temperature
|
230 to 248
|
°F
|
|
|
Drying Time
|
2.0 to 3.0
|
hr
|
|
|
Hopper Temperature
|
176 to 212
|
°F
|
|
|
Rear Temperature
|
500 to 536
|
°F
|
|
|
Middle Temperature
|
536 to 572
|
°F
|
|
|
Front Temperature
|
572 to 608
|
°F
|
|
|
Nozzle Temperature
|
536 to 572
|
°F
|
|
|
Processing (Melt) Temp
|
572 to 608
|
°F
|
|
|
Mold Temperature
|
212 to 266
|
°F
|
- Physical properties of related products: HFG300 CTI2550 V01550 V01525 V02570 V03505 V03550 S100G20 PCN2615 PCN2615H PX1340 PX2949 PX2956 ZM3640 SE1GFN3 SE1GFN1 SE1GFN2 HS2000X HM3020 HM4025 HS1000X NH7111E NH7112 NH7114 NH8006 ZM3242 ZWM2411
Correlation search: Sabic V0150B PPO V0150B V0150B-701 V0150B-WH5C017 V0150B-701474
广州华秀塑胶有限公司不仅是专业的Noryl PPO V0150B原料供应商，亦注重技术支持及全方位的解决方案，提供从材料鉴定、模具设计、成型加工等系列帮助，亦可为客户量身定制各特殊性能之Noryl PPO V0150B材料，进而协助客户提高产品竟争力。
地址:广州市天河区中山大道中439号东圃天银商贸大厦1720-1723室
电话:020-82582555
传真:020-82523699
Email: sales@va-so.cn
Noryl PPO V0150B报价 >>
常规产品
长纤增强尼龙6 长纤增强PP
长纤增强复合材料 冲击改性复合尼龙66
冲击改性复合尼龙6 高强尼龙
冲击改性复合尼龙 冲击改性复合材料
改性PP 改性的合金料
高温改性塑料 含氟聚合物
改性POM 改性PBT
改性PC 焊接用复合塑料
高比重复合塑料 永久防静电塑料
永久防静电ABS 永久防静电合金
永久防静电POM 其他导电材料
导电尼龙 导电PE,导电PP
高温导电塑料 导电POM
导电PBT 导电PC
其他非PTFE自润滑塑料 非PTFE自润滑PA
非PTFE自润滑聚苯醚 非PTFE自润滑PPA
非PTFE自润滑聚甲醛 非PTFE自润滑聚碳酸酯
其他润滑塑料 润滑尼龙
润滑烯烃 润滑PPO(PPE+PS)
耐热润滑塑料 润滑POM
润滑PBT 润滑弹性体
润滑PC 挤出PBT
热传导复合塑料 其他PC
EMI/RFI屏蔽复合塑料 预着色非填充树脂
热门工程塑胶原料
KFI12 DF008ERH IFL21 DI001L CD000I OE006C1 SCL36 LC006 357U RZ0069 DX00714H MC2123 RE0069S PH1100B DFL42 NORYL™ PPO LEXAN™ PC VALOX™ PBT ULTEM™ PEI CYCOLOY™ PC/ABS XYLEX™ PC/PET XENOY™ PC/PBT/PET Noryl GTX PPE/PA CYCOLAC™ ABS GELOY™ ASA Colorcomp Faradex Konduit Lubricomp Lubriloy Stat-kon Stat-loy Thermocomp Thermotuf Verton